The process for resetting the LCD display on your eBike may vary depending on the make and model of your bike, but here are some general steps you can try:
1. Turn off the eBike
Before attempting any resetting process, ensure that your eBike is turned off.
To turn off your eBike, you need to stop the motor and disconnect the power source. Depending on your eBike model, there may be different ways to do this. Here are some general steps:
- Stop pedaling: If your eBike has pedal-assist, stop pedaling to disengage the motor.
- Release the throttle: If your eBike has a throttle, release it to disengage the motor.
- Apply the brakes: Use the brakes to slow down and stop the eBike.
- Turn off the power: Once the eBike is stationary, locate the power button or switch and turn it off. This will disconnect the power source and turn off the motor and other electrical components.
Some eBikes may have slightly different steps to turn off the power, so consult the owner’s manual for specific instructions for your eBike model. It’s important to always turn off your eBike before attempting any maintenance or resetting processes to ensure your safety and prevent damage to the electrical components.
2. Locate the reset button
The reset button is usually located on the side of the LCD display or hidden in a tiny hole. Check the owner’s manual for specific instructions for your bike.
The reset button on an eBike is a small button usually located on the side of the LCD display, or sometimes on the controller or battery pack. The location of the reset button may vary depending on the make and model of your eBike, so it’s best to consult the owner’s manual for specific instructions.
The reset button is often small and may be difficult to see, so you may need to look closely to find it. It’s usually a circular or oblong button that can be pressed with a small tool such as a paperclip or toothpick.
If you’re having trouble locating the reset button, try checking the owner’s manual, or searching for online resources specific to your eBike model. Some manufacturers may also have videos or tutorials that demonstrate how to find and use the reset button. It’s important to follow the correct steps to reset the LCD display to prevent any accidental damage to the eBike’s components.
3. Press and hold the reset button
Using a paperclip or other small tool, press and hold the reset button for a few seconds.
Once you have located the reset button on your eBike, the next step is to press and hold the button for a few seconds.
To do this, you will need a small tool such as a paperclip or toothpick to press and hold the button. Place the tool on the button and apply gentle pressure until you feel the button click. Hold the button down for a few seconds, usually around 5-10 seconds, depending on the make and model of your eBike.
While you are holding down the reset button, it’s important to keep the eBike turned off and not to touch any other buttons or controls. Holding the reset button down for the correct amount of time will reset the LCD display and any associated settings to their default values.
Once you have held down the reset button for the correct amount of time, you can release the button and proceed to turn the eBike back on. Remember to follow the manufacturer’s instructions carefully to ensure you reset the LCD display properly and avoid any damage to your eBike’s electrical components.
4. Release the reset button
Once you have held down the reset button for a few seconds, release it.
After you have held down the reset button on your eBike for a few seconds, the next step is to release the button.
To release the reset button, simply remove your finger or the small tool you used to press the button. You should feel the button pop back up, indicating that you have successfully released it.
It’s important to release the reset button after holding it down for the appropriate amount of time, which is usually around 5-10 seconds depending on the make and model of your eBike. Holding down the reset button for too long could cause the eBike to enter into a different mode or reset to a different default setting.
Once you have released the reset button, you can proceed to turn the eBike back on and check if the LCD display has been reset to its default settings. If you have any trouble or the display is still not working properly, refer to the manufacturer’s instructions or contact their customer support for further assistance.
5. Turn on the eBike
Turn on your eBike and see if the LCD display has been reset.
After resetting the LCD display on your eBike, the next step is to turn the eBike back on. Here are the general steps to turn on an eBike:
Ensure that the eBike is in a safe and stable position.
Locate the power button or switch: This is usually located on the battery or controller, depending on the make and model of your eBike.
Turn on the power: Press and hold the power button or switch for a few seconds until you see the LCD display light up or hear a beep sound. Some eBikes may require you to press the power button or switch once, rather than holding it down.
Check the LCD display: Once the power is on, check the LCD display to ensure it is functioning properly. The display should show information such as the battery level, speed, and other relevant details about your eBike’s operation.
If the LCD display is not working properly, you may need to repeat the resetting process or seek further assistance from the manufacturer’s customer support. Always follow the manufacturer’s instructions carefully and ensure that the eBike is in a safe and stable position before turning on the power.
If these steps do not work, consult the owner’s manual for your specific eBike model, or contact the manufacturer for further assistance.
Below is a video example for resetting the displays for your reference.
